Free Toro TimeCutter SS 4225 74706 Operator's Manual PDF | Manualsnet (2024)

Form No. 3425-346 Rev A

TimeCutter SS 4225 Riding Mower Model No. 74706Serial No. 404314200 and Up

Register at www.Toro.com. Original Instructions (EN) *3425-346* A

It is a violation of California Public Resource Code Section 4442 or 4443 to use or operate the engine on any forest-covered, brush-covered, or grass-covered land unless the engine is equipped with a spark arrester, as defined in Section 4442, maintained in effective working order or the engine is constructed, equipped, and maintained for the prevention of fire.

Gross or Net Torque: The gross or net torque of this engine was laboratory rated by the engine manufacturer in accordance with the Society of Automotive Engineers (SAE) J1940 or J2723. As configured to meet safety, emission, and operating requirements, the actual engine torque on this class of mower will be significantly lower. Please refer to the engine manufacturers information included with the machine.

Go to www.Toro.com to view specifications on your model.

The enclosed engine owner's manual is supplied for information regarding the US Environmental Protection Agency (EPA) and the California Emission Control Regulation of emission systems, maintenance, and warranty. Replacements may be ordered through the engine manufacturer.

WARNING CALIFORNIA

Proposition 65 Warning The engine exhaust from this product

contains chemicals known to the State of California to cause cancer, birth defects,

or other reproductive harm. Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause

cancer and reproductive harm. Wash hands after handling.

Use of this product may cause exposure to chemicals known to the State of

California to cause cancer, birth defects, or other reproductive harm.

Introduction This rotary-blade, riding lawn mower is intended to be used by homeowners in residential applications. It is designed primarily for cutting grass on well-maintained lawns.

Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely.

Visit www.Toro.com for product safety and operation training materials, accessory information, help finding a dealer, or to register your product.

Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product. Write the numbers in the space provided.

Important: With your mobile device, you can scan the QR code on the serial number decal (if equipped) to access warranty, parts, and other product information.

g235765

Figure 1

1. Model and serial number plate

Write the product model and serial numbers in the space below:

Model No.

Serial No.

This manual uses 2 words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention.

2019The Toro Company 8111 Lyndale Avenue South Bloomington, MN 55420 2

Contact us at www.Toro.com. Printed in the USA All Rights Reserved

Contents Safety ....................................................................... 4

Safety Alert Symbol ............................................ 4 General Safety ................................................... 4 Slope Indicator ................................................... 5 Safety and Instructional Decals .......................... 6

Product Overview ................................................... 12 Controls ........................................................... 12

Before Operation ................................................. 14 Before Operation Safety ................................... 14 Pre-Start ........................................................... 14 Fuel Safety ....................................................... 15 Adding Fuel ...................................................... 16 Performing Daily Maintenance.......................... 16 Breaking in a NewMachine .............................. 16 Using the Safety-Interlock System.................... 17 Positioning the Seat.......................................... 17 Adjusting theMotion-Control Levers ................. 18

During Operation ................................................. 18 During Operation Safety ................................... 18 Operating the Mower Blade-Control Switch (PTO) ............................................................ 20

Operating the Throttle....................................... 21 Operating the Choke ........................................ 21 Starting the Engine ........................................... 21 Shutting Off the Engine..................................... 22 Using theMotion-Control Levers....................... 22 Driving the Machine.......................................... 22 Using the Side Discharge ................................. 24 Adjusting the Height of Cut ............................... 24 Adjusting the Anti-Scalp Rollers........................ 25 Operating Tips ................................................. 25

After Operation .................................................... 26 After Operation Safety ...................................... 26 Pushing the Machine by Hand .......................... 29

Maintenance ........................................................... 30 Maintenance Safety.......................................... 30

RecommendedMaintenance Schedule(s) ........... 31 Pre-Maintenance Procedures .............................. 32 Raising the Seat ............................................... 32

Lubrication .......................................................... 32 Greasing the Bearings ...................................... 32

Engine Maintenance ........................................... 33 Engine Safety ................................................... 33 Servicing the Air Cleaner .................................. 33 Servicing the Engine Oil.................................... 33 Servicing the Spark Plug................................... 36 Cleaning the Cooling System............................ 36

Fuel SystemMaintenance ................................... 37 Replacing the In-Line Fuel Filter ....................... 37

Electrical SystemMaintenance ........................... 38 Electrical System Safety ................................... 38 Servicing the Battery......................................... 38 Servicing the Fuses .......................................... 39

Drive SystemMaintenance .................................. 40 Checking the Tire Pressure............................... 40 Releasing the Electric Brake............................. 40

Belt Maintenance ................................................ 41 Inspecting the Belts .......................................... 41 Replacing the Mower Belt ................................. 41

Mower Maintenance............................................. 42 Blade Safety ..................................................... 42 Servicing the Cutting Blades............................. 42 Leveling the Mower Deck.................................. 44 Removing the Mower Deck............................... 46 Installing the Mower Deck................................. 47 Replacing the Grass Deflector .......................... 47

Cleaning .............................................................. 48 Washing the Underside of the Mower Deck.............................................................. 48

Disposing of Waste........................................... 49 Storage ................................................................... 49

Storage Safety.................................................. 49 Cleaning and Storage....................................... 49 Storing the Battery............................................ 50

Troubleshooting ...................................................... 51 Schematics ............................................................. 53

3

Safety The following instructions are from ANSI standard B71.1-2017.

Safety Alert Symbol This Safety Alert Symbol (Figure 2) is used both in this manual and on the machine to identify important safety messages which must be followed to avoid accidents.

This symbol means: ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

g000502

Figure 2 Safety Alert Symbol

The safety alert symbol appears above information which alerts you to unsafe actions or situations and will be followed by the word DANGER,WARNING, or CAUTION.

DANGER: Indicates an imminently hazardous situation which, if not avoided, Will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, Could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, May result in minor or moderate injury.

This manual uses two other words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention.

General Safety This machine is capable of amputating hands and feet and of throwing objects. Toro designed and tested this lawn mower to offer reasonably safe service; however, failure to comply with safety instructions may result in injury or death. Read, understand, and follow all instructions and

warnings in the Operators Manual and other training material, on the machine, engine, and attachments. All operators and mechanics should be trained. If the operator(s) or mechanic(s) can not read this manual, it is the owners responsibility to explain this material to them; other languages may be available on our website.

Only allow trained, responsible, and physically capable operators that are familiar with the safe operation, operator controls, and safety signs and instructions to operate the machine. Never let children or untrained people operate or service the equipment. Local regulations may restrict the age of the operator.

Do Not operate the machine near drop-offs, ditches, embankments, water, or other hazards, or on slopes greater than 15 degrees.

Do Not put your hands or feet near moving components of the machine.

Never operate the machine with damaged guards, shields, or covers. Always have safety shields, guards, switches and other devices in place and in proper working condition.

Stop the machine, shut off the engine, and remove the key before servicing, fueling, or unclogging the machine.

4

Slope Indicator

g011841

Figure 3 You may copy this page for personal use.

1. The maximum slope you can operate the machine on is 15 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope.

2. Align this edge with a vertical surface, a tree, building, fence pole, etc. 3. Example of how to compare slope with folded edge

5

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing.

decalbatterysymbols

Battery Symbols Some or all of these symbols are on your battery.

1. Explosion hazard 6. Keep bystanders away from the battery.

2. No fire, open flame, or smoking

7. Wear eye protection; explosive gases can cause blindness and other injuries.

3. Caustic liquid/chemical burn hazard

8. Battery acid can cause blindness or severe burns.

4. Wear eye protection. 9. Flush eyes immediately with water and get medical help fast.

5. Read the Operator's Manual.

10. Contains lead; do not discard

decaloemmarkt

Manufacturer's Mark

1. Indicates the blade is identified as a part from the original machine manufacturer.

decal93-7009

93-7009

1. Warningdo not operate the mower with the deflector up or removed; keep the deflector in place.

2. Cutting/dismemberment hazard of hand or foot, mower bladestay away from moving parts.

decal105-7015

105-7015

1. Belt routing

decal106-8717

106-8717

1. Read the instructions before servicing or performing maintenance.

2. Check tire pressure every 25 operating hours. 3. Grease every 25 operating hours. 4. Engine

decal119-8814

119-8814

1. Parking position 4. Neutral 2. Fast 5. Reverse 3. Slow

6

decal119-8815

119-8815

1. Parking position 4. Neutral 2. Fast 5. Reverse 3. Slow

decal119-8871

119-8871

1. Height of cut 2. 4-1/2 inches 3. 4 inches 4. 3-1/2 inches 5. 3 inches 6. 2-1/2 inches 7. 2 inches 8. 1-1/2 inches

7

decal121-0772

121-0772

1. Fast 4. Choke 2. Continuous variable setting 5. Power take-off (PTO), Blade control switch 3. Slow

8

decal121-2989b

121-2989

1. Bypass lever position for pushing the machine

2. Bypass lever position for operating the machine

decal131-3947

131-3947

1. Trimslow 3. Mowfast 2. Towmedium

9

decal132-0869

132-0869 Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum recommended slope indicated on the decal. Review the instructions for operating the machine on slopes in the Operators Manual as well as the conditions in which you would operate the machine to determine whether you can operate the machine in the conditions on that day and at that site. Changes in the terrain can result in a change in slope operation for the machine. If possible, keep the cutting units lowered to the ground while operating the machine on slopes. Raising the cutting units while operating on slopes can cause the machine to become unstable.

1. Warningread the Operator's Manual.

3. Cutting/dismemberment hazard of the hand, mower blade; entanglement hazard of the hand, beltstay away from moving parts; keep all guards and shields in place.

5. Ramp hazarddo not use dual ramps when loading onto a trailer; use 1 ramp wide enough for the machine; use a ramp with a slope less than 15; back up the ramp when loading the machine and drive forward off the ramp when unloading.

7. Tipping hazarddo not use on slopes near open water; do not use on slopes greater than 15.

2. Warningbefore performing maintenance, read theOperator's Manual; engage the parking brake, remove the key, and disconnect the spark plug.

4. Thrown object hazardkeep bystanders away; pick up debris before operating; lower the deflector before using the machine.

6. Runover/backover hazarddo not carry passengers; look behind you when mowing in reverse.

10

decal132-0872

132-0872

1. Thrown object hazardkeep bystanders away from the machine.

3. Severing hazard of hand or footkeep away from moving parts.

2. Thrown object hazard, raised baffledo not operate the machine with an open deck; use a bagger or a baffle.

4. Entanglement hazardkeep away from moving parts; keep all guards and shields in place.

decal133-8062

133-8062

11

Product Overview

g028411

Figure 4

1. Footrest 8. Gas-tank cap 2. Deflector 9. Smart Speed lever 3. Height-of-cut lever 10. Rear drive wheel 4. Motion-control lever 11. Mower deck 5. Control panel 12. Anti-scalp roller 6. Operator seat 13. Front caster wheel 7. Engine

Controls Become familiar with all the controls before you start the engine and operate the machine.

Control Panel

g032603

Figure 5

1. Throttle control 3. Blade-control switch (power takeoff)

2. Choke control 4. Key switch

Key Switch The key switch, used to start and shut off the engine, has 3 positions: OFF, RUN, and START. Refer to Starting the Engine (page 21).

Throttle Control The throttle controls the engine speed, and it has a continuous-variable setting from the SLOW to FAST position (Figure 5).

Choke Control Use the choke control to start a cold engine.

Blade-Control Switch (Power Takeoff) The blade-control switch, represented by a power-takeoff (PTO) symbol, engages and disengages power to the mower blades (Figure 5).

Motion-Control Levers Use the motion-control levers to drive the machine forward, reverse, and turn either direction (Figure 4).

12

Park Position Move the motion-control levers outward from the center to the PARK position when exiting the machine (Figure 17). Always position the motion-control levers into the PARK position when you stop the machine or leave it unattended.

Smart Speed Control System Lever The Smart Speed Control-System lever, located below the operating position, gives you a choice to drive the machine at 3 speed ranges trim, tow, and mow (Figure 20).

Fuel-Presence Window You can use the fuel window, located on the left side of the machine, to verify the presence of fuel in the tank (Figure 6).

g014521

Figure 6

1. Fuel-presence window

Height-of-Cut Lever Use the height-of-cut lever to lower and raise the deck from the seated position. Moving the lever up (toward you) raises the deck from the ground and moving the lever down (away from you) lowers the deck toward the ground. Adjust the height-of-cut only while the machine is not moving (Figure 21).

Attachments/Accessories A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or authorized Toro distributor or go to www.Toro.com for a list of all approved attachments and accessories.

To ensure optimum performance and continued safety certification of the machine, use only genuine Toro replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be dangerous, and such use could void the product warranty.

13

Operation Note: Determine the left and right sides of the machine from the normal operating position.

Before Operation Before Operation Safety Evaluate the terrain to determine what accessories

and attachments are needed to properly and safely perform the job. Only use accessories and attachments approved by Toro.

Inspect the area where the equipment is to be used and remove all rocks, toys, sticks, wires, bones, and other foreign objects. These can be thrown or interfere with the operation of the machine and may cause personal injury to the operator or bystanders.

Wear appropriate personal protective equipment such as safety glasses, substantial slip-resistant footwear, and hearing protection. Tie back long hair and avoid loose clothing and loose jewelry which may get tangled in moving parts.

CAUTION This machine produces sound levels in excess of 85 dBA at the operators ear and can cause hearing loss through extended periods of exposure. Wear hearing protection when operating this machine.

Check that the operator presence controls, safety switches, and shields are attached and functioning properly. Do Not operate unless they are functioning properly.

Do Not operate the mower when people, especially children, or pets are in the area. Stop the machine and attachment(s) if anyone enters the area.

Do Not operate the machine without the entire grass collection system, discharge deflector, or other safety devices in place and in proper working condition. Grass catcher components are subject to wear, damage and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check for worn or deteriorating components and replace them with the manufacturers recommended parts when necessary.

Pre-Start Fill fuel tank on level ground. See Fuel Recommendations in the Specifications section for additional gasoline information.

Do Not add oil to gasoline.

Do Not overfill fuel tank. Fill the fuel tank to the bottom of the filler neck. The empty space in the tank allows gasoline to expand. Overfilling may result in fuel leakage or damage to the engine or emission system.

Make sure you understand the controls, their locations, their functions, and their safety requirements.

Refer to the Maintenance section and perform all the necessary inspection and maintenance steps.

14

Fuel Safety Use extreme care when handling fuel.

DANGER In certain conditions gasoline is extremely flammable and vapors are explosive. A fire or explosion from gasoline can burn you, others, and cause property damage. Fill the fuel tank outdoors on level ground,

in an open area, when the engine is cold. Wipe up any gasoline that spills.

Never refill the fuel tank or drain the machine indoors or inside an enclosed trailer.

Do Not fill the fuel tank completely full. Fill the fuel tank to the bottom of the filler neck. The empty space in the tank allows gasoline to expand. Overfilling may result in fuel leakage or damage to the engine or emission system.

Never smoke when handling gasoline, and stay away from an open flame or where gasoline fumes may be ignited by spark.

Store gasoline in an approved container and keep it out of the reach of children.

Add fuel before starting the engine. Never remove the cap of the fuel tank or add fuel when engine is running or when the engine is hot.

If fuel is spilled, Do Not attempt to start the engine. Move away from the area of the spill and avoid creating any source of ignition until fuel vapors have dissipated.

Do Not operate without entire exhaust system in place and in proper working condition.

DANGER In certain conditions during fueling, static electricity can be released causing a spark which can ignite gasoline vapors. A fire or explosion from gasoline can burn you and others and cause property damage. Always place gasoline containers on the

ground away from your vehicle before filling.

Do Not fill gasoline containers inside a vehicle or on a truck or trailer bed because interior carpets or plastic truck bed liners may insulate the container and slow the loss of any static charge.

When practical, remove gas-powered equipment from the truck or trailer and refuel the equipment with its wheels on the ground.

If this is not possible, then refuel such equipment on a truck or trailer from a portable container, rather than from a gasoline dispenser nozzle.

If a gasoline dispenser nozzle must be used, keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do Not use a nozzle lock open device.

WARNING Gasoline is harmful or fatal if swallowed. Long-term exposure to vapors has caused cancer in laboratory animals. Failure to use caution may cause serious injury or illness. Avoid prolonged breathing of vapors. Keep face away from nozzle and gas

tank/container opening. Keep away from eyes and skin. Never siphon by mouth.

To help prevent fires: Keep engine and engine area free from

accumulation of grass, leaves, excessive grease or oil, and other debris which can accumulate in these areas.

Clean up oil and fuel spills and remove fuel soaked debris.

Allow the machine to cool before storing the machine in any enclosure. Do Not store near flame or any enclosed area where open pilot lights or heat appliances are present.

15

Adding Fuel Recommended Fuel For best results, use only clean, fresh (less than

30 days old), unleaded gasoline with an octane rating of 87 or higher ((R+M)/2 rating method).

Ethanol: Gasoline with up to 10% ethanol (gasohol) or 15% MTBE (methyl tertiary butyl ether) by volume is acceptable. Ethanol and MTBE are not the same. Gasoline with 15% ethanol (E15) by volume is not approved for use. Never use gasoline that contains more than 10% ethanol by volume, such as E15 (contains 15% ethanol), E20 (contains 20% ethanol), or E85 (contains up to 85% ethanol). Using unapproved gasoline may cause performance problems and/or engine damage which may not be covered under warranty.

Do not use gasoline containing methanol. Do not store fuel either in the fuel tank or fuel

containers over the winter unless you use a fuel stabilizer.

Do not add oil to gasoline.

Using Stabilizer/Conditioner Use a fuel stabilizer/conditioner in the machine to provide the following benefits: Keeps fuel fresh longer when used as directed by

the fuel-stabilizer manufacturer Cleans the engine while it runs Eliminates gum-like varnish buildup in the fuel

system, which causes hard starting

Important: Do not use fuel additives containing methanol or ethanol. Add the correct amount of fuel stabilizer/conditioner to the fuel.

Note: A fuel stabilizer/conditioner is most effective when mixed with fresh fuel. To minimize the chance of varnish deposits in the fuel system, use fuel stabilizer at all times.

Filling the Fuel Tank 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the engine and remove the key. 4. Clean around the fuel-tank cap. 5. Fill the fuel tank to the bottom of the filler neck

(Figure 7).

Note: Do not fill the fuel tank completely full. The empty space in the tank allows the fuel to expand.

g027243

Figure 7

Performing Daily Maintenance Before starting the machine each day, perform the Each Use/Daily procedures listed in Maintenance (page 30).

Breaking in a New Machine New engines take time to develop full power. Mower decks and drive systems have higher friction when new, placing additional load on the engine. Allow 40 to 50 hours of break-in time for new machines to develop full power and best performance.

16

Using the Safety-Interlock System

WARNING If the safety-interlock switches are disconnected or damaged, the machine could operate unexpectedly, causing personal injury. Do not tamper with the interlock switches. Check the operation of the interlock

switches daily and replace any damaged switches before operating the machine.

Understanding the Safety-Interlock System The safety-interlock system is designed to prevent the engine from starting unless: The blade-control switch (PTO) is disengaged. The motion-control levers are in the PARK position.

The safety-interlock system also is designed to shut off the engine whenever the control levers are out of the PARK position and you rise from the seat.

Testing the Safety-Interlock System Test the safety-interlock system before you use the machine each time. If the safety system does not operate as described below, have an Authorized Service Dealer repair the safety system immediately. 1. Sit on the seat, move the motion-control levers

in the PARK position, and move the blade-control switch to the ON position. Try starting the engine; the engine should not crank.

2. Sit on the seat and move the blade-control switch to the OFF position. Move either motion-control lever to the center, unlocked position. Try starting the engine; the engine should not crank. Repeat with the other motion-control lever.

3. Sit on the seat, move the blade-control switch to the OFF position, and lock the motion-control levers in the PARK position. Start the engine. While the engine is running, engage the blade-control switch, and rise slightly from the seat; the engine should shut off.

4. Sit on the seat, move the blade-control switch to the OFF position, and lock the motion-control levers in the PARK position. Start the engine. While the engine is running, move the

motion-control levers to the center, unlocked position, engage the blade-control switch, and rise slightly from the seat; the engine should shut off.

Positioning the Seat The seat can move forward and backward. Position the seat where you have the best control of the machine and are most comfortable (Figure 8).

g027249

Figure 8

17

Adjusting the Motion-Control Levers Adjusting the Height You can adjust the motion-control levers higher or lower for maximum comfort (Figure 9).

g027252

Figure 9

Adjusting the Tilt You can adjust the motion-control levers forward or rearward for your comfort. 1. Loosen the upper bolt holding the control lever

to the control-arm shaft. 2. Loosen the lower bolt just enough to pivot the

control lever forward or rearward (Figure 9). 3. Tighten both bolts to secure the control lever in

the new position. 4. Repeat the adjustment for the other control lever.

During Operation During Operation Safety General Safety The operator must use their full attention when operating the machine. Do Not engage in any activity that causes distractions; otherwise, injury or property damage may occur.

WARNING Operating engine parts, especially the muffler, become extremely hot. Severe burns can occur on contact and debris, such as leaves, grass, brush, etc. can catch fire. Allow engine parts, especially the muffler,

to cool before touching. Remove accumulated debris from muffler

and engine area.

WARNING Engine exhaust contains carbon monoxide, which is an odorless deadly poison that can kill you. Do Not run engine indoors or in a small confined area where dangerous carbon monoxide fumes can collect. The owner/user can prevent and is responsible

for accidents or injuries occurring to himself or herself, other people or property.

This mower was designed for one operator only. Do not carry passengers and keep all others away from machine during operation.

Do Not operate the machine under the influence of alcohol or drugs.

Operate only in daylight or good artificial light. Lightning can cause severe injury or death. If

lightning is seen or thunder is heard in the area, Do Not operate the machine; seek shelter.

Use extra care while operating with accessories or attachments, such as grass collection systems. These can change the stability of the machine and cause a loss of control. Follow directions for counter weights if required.

Keep away from holes, ruts, bumps, rocks, and other hidden hazards. Use care when approaching blind corners, shrubs, trees, tall grass or other objects that may hide obstacles or obscure vision. Uneven terrain could overturn the machine or cause the operator to lose their balance or footing.

18

Be sure all drives are in neutral and parking brake is engaged before starting engine.

Start the engine carefully according to instructions with feet well away from the blades.

Never operate the mower with damaged guards, shields, or covers. Always have safety shields, guards, switches and other devices in place and in proper working condition.

Keep clear of the discharge opening at all times. Never mow with the discharge door raised, removed or altered unless there is a grass collection system or mulch kit in place and working properly.

Keep hands and feet away from moving parts. If possible, Do Not make adjustments with the engine running.

WARNING Hands, feet, hair, clothing, or accessories can become entangled in rotating parts. Contact with the rotating parts can cause traumatic amputation or severe lacerations. Do Not operate the machine without

guards, shields, and safety devices in place and working properly.

Keep hands, feet, hair, jewelry, or clothing away from rotating parts.

Never raise the deck with blades running. Be aware of the mower discharge path and direct

discharge away from others. Avoid discharging material against a wall or obstruction as the material may ricochet back toward the operator. Stop the blades, slow down, and use caution when crossing surfaces other than grass and when transporting the mower to and from the area to be mowed.

Be alert, slow down and use caution when making turns. Look behind and to the side before changing directions. Do Not mow in reverse unless absolutely necessary.

Do Not change the engine governor setting or overspeed the engine.

Park the machine on level ground. Stop engine, wait for all moving parts to stop, and remove the spark plug wire(s). Before checking, cleaning or working on the

mower. After striking a foreign object or abnormal

vibration occurs (inspect the mower for damage and make repairs before restarting and operating the mower).

Before clearing blockages.

Whenever you leave the mower. Do Not leave a running machine unattended.

Stop engine, wait for all moving parts to stop: Before refueling. Before dumping the grass catcher. Before making height adjustments.

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. Keep children out of the mowing area and

under the watchful care of another responsible adult, not the operator.

Be alert and turn the machine off if children enter the area.

Before and while backing or changing direction, look behind, down, and side-to-side for small children.

Never allow children to operate the machine. Do Not carry children, even with the blades

shut off. Children could fall off and be seriously injured or interfere with the safe operation of the machine. Children that have been given rides in the past could suddenly appear in the working area for another ride and be run over or backed over by the machine.

Slope Safety Slopes are a major factor related to loss of control

and rollover accidents, which can result in severe injury or death. The operator is responsible for safe slope operation. Operating the machine on any slope requires extra caution. Before using the machine on a slope, the operator must: Review and understand the slope instructions

in the manual and on the machine. Use an angle indicator to determine the

approximate slope angle of the area. Never operate on slopes greater than 15

degrees. Evaluate the site conditions of the day to

determine if the slope is safe for machine operation. Use common sense and good judgment when performing this evaluation. Changes in the terrain, such as moisture, can quickly affect the operation of the machine on a slope.

Identify hazards at the base of the slope. Do Not operate the machine near drop offs, ditches, embankments, water or other hazards. The machine could suddenly roll over if a wheel goes over the edge or the edge collapses. Keep a safe

19

distance (twice the width of the machine) between the machine and any hazard. Use a walk behind machine or a hand trimmer to mow the grass in these areas.

g229111

Figure 10

1. Safe Zone-Use the mower here on slopes less than 15 degrees

2. Danger Zone-Use a walk-behind mower and/or hand trimmer on slopes greater than 15 degrees

3. Water 4. W=width of the machine 5. Keep a safe distance (twice the width of the machine)

between the machine and any hazard.

Avoid starting, stopping or turning the machine on slopes. Avoid making sudden changes in speed or direction; turn slowly and gradually.

Do Not operate a machine under any conditions where traction, steering or stability is in question. Be aware that operating the machine on wet grass, across slopes or downhill may cause the machine to lose traction. Loss of traction to the drive wheels may result in sliding and a loss of braking and steering. The machine can slide even if the drive wheels are stopped.

Remove or mark obstacles such as ditches, holes, ruts, bumps, rocks or other hidden hazards. Tall grass can hide obstacles. Uneven terrain could overturn the machine.

Use extra care while operating with accessories or attachments, such as grass collection systems. These can change the stability of the machine and cause a loss of control. Follow directions for counter weights.

If possible, keep the deck lowered to the ground while operating on slopes. Raising the deck while operating on slopes can cause the machine to become unstable.

Operating the Mower Blade-Control Switch (PTO) The blade-control switch (PTO) starts and stops the mower blades and any powered attachments.

Engaging the Blade-Control Switch (PTO)

g008945

Figure 11

Note: Always engage the blades with the throttle in the FAST position (Figure 12).

g187516

Figure 12

Disengaging the Blade-Control Switch (PTO)

g009174

Figure 13

20

Operating the Throttle You can move the throttle control between FAST and SLOW positions (Figure 14).

Always use the FAST position when engaging the PTO.

g187517

Figure 14

Operating the Choke Use the choke to start a cold engine. 1. Pull up the choke knob to engage the choke

before using the key switch (Figure 15). 2. Push down the choke knob to disengage the

choke after the engine has started (Figure 15).

g008959

Figure 15

1. ON position 2. OFF position

Starting the Engine Note: A warm or hot engine may not require choking.

Important: Do not engage the starter for more than 5 seconds at a time. Engaging the starter motor for more than 5 seconds can damage the starter motor. If the engine fails to start, wait 10 seconds before operating the engine starter again.

g027581

Figure 16

21

Shutting Off the Engine 1. Disengage the blades by moving the

blade-control switch to the OFF position (Figure 16).

2. Engage the parking brake; refer to Park Position (page 13).

3. Move the throttle lever to the SLOW position and let the engine idle for 1 minute.

4. Turn the key to the OFF position and remove the key.

CAUTION Children or bystanders may be injured if they move or attempt to operate the machine while it is unattended. Always remove the key and engage the parking brake when leaving the machine unattended.

Using the Motion-Control Levers

g004532

Figure 17

1. Motion-control leverPARK position

4. Backward

2. Center, unlocked position 5. Front of machine 3. Forward

Driving the Machine The drive wheels turn independently, powered by hydraulic motors on each axle. You can turn 1 side in reverse while you turn the other forward, causing the machine to spin rather than turn. This greatly improves the machine maneuverability but may require sometime for you to adapt to how it moves.

The throttle control regulates the engine speed as measured in rpm (revolutions per minute). Place the throttle control in the FAST position for best performance. Always operate in the full throttle position when mowing.

WARNING The machine can spin very rapidly. You may lose control of the machine and cause personal injury or damage to the machine. Use caution when making turns. Slow the machine down before making

sharp turns.

Driving Forward Note: Always use caution when backing up and turning. 1. Move the levers to the center, unlocked position. 2. To go forward, slowly push the motion-control

levers forward (Figure 18).

g008952

Figure 18

Driving Backward 1. Move the levers to the center, unlocked position.

22

2. To go backward, slowly pull the motion-control levers rearward (Figure 19).

g008953

Figure 19

Using the Smart SpeedTM Control System The Smart Speed TM Control-System lever, located below the operating position (Figure 20), gives the operator a choice to drive the machine at 3 ground speed rangestrim, tow, and mow.

g027625

Figure 20

1. Smart-speed lever

To change speeds, do the following: 1. Move the motion-control levers to neutral and

outward to the PARK position. 2. Disengage the blade-control switch. 3. Adjust the lever to the desired position.

The following are only recommendations for use. Adjustments vary by grass type, moisture content, and the height of the grass.

Suggested uses:

Trim Tow Mow

Parking X

Heavy, wet grass

X

Training X

Trimming grass

X

Bagging X

Mulching X

Towing attachments

X

Normal mowing

X

Moving the machine

X

Trim

This is the lowest speed. The suggested uses for this speed are as follows: Parking Heavy, wet grass mowing conditions Training Trimming grass

Tow

This is the medium speed. The suggested uses for this speed are as follows: Bagging Mulching Towing attachments

Mow

This is the fastest speed. The suggested uses for this speed are as follows: Normal mowing Moving the machine

23

Using the Side Discharge The mower has a hinged grass deflector that disperses clippings to the side and down toward the turf.

DANGER Without a grass deflector, discharge cover, or a complete grass-catcher assembly mounted in place, you and others are exposed to blade contact and thrown debris. Contact with rotating mower blade(s) and thrown debris will cause injury or death. Never remove the grass deflector from the

mower deck because the grass deflector routes material down toward the turf. If the grass deflector is ever damaged, replace it immediately.

Never put your hands or feet under the mower deck.

Never try to clear the discharge area or mower blades unless you move the blade-control switch (PTO) to the OFF position, rotate the key switch to the OFF position, and remove the key from the key switch.

Make sure that the grass deflector is in the down position.

Adjusting the Height of Cut Note: The transport position is the highest height-of-cut position or cutting height at 115 mm (4-1/2 inches) as shown in Figure 21.

Height of cut is controlled by the lever located to the right of the operating position (Figure 21).

g028025

Figure 21

24

Adjusting the Anti-Scalp Rollers For Machine with 107 cm (42-inch) Mower Decks Only Whenever you change the height of cut, adjust the height of the anti-scalp rollers.

Note: Adjust the anti-scalp rollers so that the rollers do not touch the ground in normal, flat mowing areas. 1. Park the machine on a level surface, disengage

the blade-control switch and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Adjust the anti-scalp rollers to 1 of the following positions: Upper holeuse this position with the mower

deck in the 63 mm (2-1/2 inches) and below the height-of-cut positions (Figure 22).

Lower holeuse this position with the mower deck in the 76 mm (3 inches) and above the height-of-cut positions (Figure 22).

g019929

Figure 22

1. Anti-scalp roller 4. Upper holethe mower deck in the 63 mm (2-1/2 inches) and below the height-of-cut positions

2. Lower holethe mower deck in the 76 mm (3 inches) and above the height-of-cut positions

5. Bolt

3. Flange nut

Operating Tips Using the Fast Throttle Setting For best mowing and maximum air circulation, operate the engine at the FAST position. Air is required to thoroughly cut grass clippings, so do not set the height-of-cut so low as to totally surround the mower deck in uncut grass. Always try to have 1 side of the mower deck free from uncut grass, which allows air to be drawn into the mower deck.

Cutting a Lawn for the First Time Cut grass slightly longer than normal to ensure that the cutting height of the mower deck does not scalp any uneven ground. However, the cutting height used in the past is generally the best one to use. When cutting grass longer than 15 cm (6 inches) tall, you may want to cut the lawn twice to ensure an acceptable quality of cut.

Cutting a Third of the Grass Blade It is best to cut only about a third of the grass blade. Cutting more than that is not recommended unless grass is sparse, or it is late fall when grass grows more slowly.

Alternating the Mowing Direction Alternate the mowing direction to keep the grass standing straight. This also helps disperse clippings, which enhances decomposition and fertilization.

Mowing at Correct Intervals Grass grows at different rates at different times of the year. To maintain the same cutting height, mow more often in early spring. As the grass growth rate slows in mid summer, mow less frequently. If you cannot mow for an extended period, first mow at a high cutting height, then mow again 2 days later at a lower height setting.

Using a Slower Cutting Speed To improve cut quality, use a slower ground speed in certain conditions.

Avoiding Cutting Too Low When mowing uneven turf, raise the cutting height to avoid scalping the turf.

Stopping the Machine If you must stop the forward motion of the machine while mowing, a clump of grass clippings may

25

drop onto your lawn. To avoid this, move onto a previously cut area with the blades engaged or you can disengage the mower deck while moving forward.

Keeping the Underside of the Mower Deck Clean Clean clippings and dirt from the underside of the mower deck after each use. If grass and dirt build up inside the mower deck, cutting quality will eventually become unsatisfactory.

Maintaining the Blade(s) Maintain a sharp blade throughout the cutting season because a sharp blade cuts cleanly without tearing or shredding the grass blades. Tearing and shredding turns grass brown at the edges, which slows growth and increases the chance of disease. Check the mower blades after each use for sharpness, and for any wear or damage. File down any nicks and sharpen the blades as necessary. If a blade is damaged or worn, replace it immediately with a genuine Toro replacement blade.

After Operation After Operation Safety General Safety Park machine on level ground, disengage drives,

set parking brake, stop engine, remove key or disconnect spark plug wire. Wait for all movement to stop and allow the machine to cool before adjusting, cleaning, repairing, or storing. Never allow untrained personnel to service machine.

Clean the machine as stated in the Maintenance section. Keep engine and engine area free from accumulation of grass, leaves, excessive grease or oil, and other debris which can accumulate in these areas. These materials can become combustible and may result in a fire.

Frequently check for worn or deteriorating components that could create a hazard. Tighten loose hardware.

Transporting

Transporting the Machine Use a heavy-duty trailer or truck to transport the machine. Ensure that the trailer or truck has all necessary lighting and marking as required by law. Thoroughly read all of the safety instructions. Knowing this information could help you, your family, pets, or bystanders avoid injury.

To transport the machine: Lock the brake and block the wheels. Be sure the fuel shut-off valve is closed. Securely fasten the machine to the trailer or

truck with straps, chains, cable, or ropes. Only use the four designated tie-down locations on the mowertwo on the left side and two on the right (Figure 23). Use these locations even when transporting the mower with an attached accessory. Using non-designated locations may cause damage to the mower and/or attachment.

26

g027708

Figure 23

1. Tie-down location

Secure a trailer to the towing vehicle with safety chains.

WARNING Driving on the street or roadway without turn signals, lights, reflective markings, or a slow moving vehicle emblem is dangerous and can lead to accidents causing personal injury. Do not drive machine on a public street or roadway.

Loading the Machine Use extreme caution when loading or unloading machines onto a trailer or a truck. Use a full-width ramp that is wider than the machine for this procedure. Back up ramps and drive forward down ramps (Figure 24).

g027995

Figure 24

1. Back up ramps 2. Drive forward down ramps

Important: Do not use narrow individual ramps for each side of the machine.

Ensure the ramp is long enough so that the angle with the ground does not exceed 15 degrees (Figure 25). On flat ground, this requires a ramp to be at least four times (4X) as long as the height of the trailer or truck bed to the ground. A steeper angle may cause mower components to get caught as the unit moves from the ramp to the trailer or truck. Steeper angles may also cause the machine to tip or lose control. If loading on or near a slope, position the trailer or truck so that it is

on the down side of the slope and the ramp extends up the slope. This will minimize the ramp angle.

WARNING Loading a machine onto a trailer or truck increases the possibility of tip-over and could cause serious injury or death. Use extreme caution when operating a

machine on a ramp. Use only a full-width ramp; do not use

individual ramps for each side of the machine.

Do not exceed a 15-degree angle between the ramp and the ground or between the ramp and the trailer or truck.

Ensure the length of ramp is at least four times (4X) as long as the height of the trailer or truck bed to the ground. This will ensure that ramp angle does not exceed 15 degrees on flat ground.

Back up ramps and drive forward down ramps.

Avoid sudden acceleration or deceleration while driving the machine on a ramp as this could cause a loss of control or a tip-over situation.

27

g027996

Figure 25

1. Full-width ramp in stowed position

4. Ramp is at least four times (4X) as long as the height of the trailer or truck bed to the ground

2. Side view of full-width ramp in loading position

5. H= height of the trailer or truck bed to the ground

3. Not greater than 15 degrees

6. Trailer

Towing the Machine Do not attach towed equipment except at the hitch

point. Follow the attachment manufacturer's

recommendation for weight limits for towed equipment and towing on slopes. Towed weight must not exceed the weight of the machine, operator, and ballast; otherwise hydrostatic transmission failure may occur. Use counterweights or wheel weights as described in the attachment manufacturer's manual.

Never allow children or others in or on towed equipment.

On slopes, the weight of the towed equipment may cause loss of traction, increased risk of rollover,

and loss of control. Reduce the towed weight and slow down.

Stopping distance increases with the weight of the towed load. Travel slowly and allow extra distance to stop.

Make wide turns to keep the attachment clear of the machine.

28

Pushing the Machine by Hand Important: Always push the machine by hand. Do not tow the machine, because towing may damage it.

This machine has an electric-brake mechanism, and to push the machine, the key must be in the RUN position. The battery needs to be charged and functioning to disengage the electric brake.

Pushing the Machine 1. Park the machine on a level surface, disengage

the blade-control switch, and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Locate the bypass levers on the frame on both sides of the engine.

4. Move the bypass levers forward through the key hole and down to lock them in place (Figure 26).

Note: Do this for each lever. 5. Turn the ignition key on and disengage the

parking brake.

Note: Do not start the machine.

g017303

Figure 26

1. Bypass-lever locations 3. Lever position for pushing the machine

2. Lever position for operating the machine

6. When finished, ensure that the key has been returned to the STOP position to avoid draining the battery charge.

Operating the Machine Move the bypass levers rearward through the keyhole and down to lock them in place as shown in Figure 26.

Note: Do this for each lever.

29

Maintenance Note: Determine the left and right sides of the machine from the normal operating position.

Maintenance Safety WARNING

While maintenance or adjustments are being made, someone could start the engine. Accidental starting of the engine could seriously injure you or other bystanders. Remove the key from the ignition switch, engage parking brake, and pull the wire(s) off the spark plug(s) before you do any maintenance. Also push the wire(s) aside so it does not accidentally contact the spark plug(s).

WARNING The engine can become very hot. Touching a hot engine can cause severe burns. Allow the engine to cool completely before service or making repairs around the engine area.

Park machine on level ground, disengage drives, set parking brake, stop engine, remove key or disconnect spark plug wire. Wait for all movement to stop and allow the machine to cool before adjusting, cleaning or repairing. Never allow untrained personnel to service machine.

Disconnect battery or remove spark plug wire before making any repairs. Disconnect the negative terminal first and the positive last. Reconnect positive first and negative last.

Keep the machine, guards, shields and all safety devices in place and in safe working condition. Frequently check for worn or deteriorating components and replace them with the manufacturers recommended parts when necessary.

WARNING Removal or modification of original equipment, parts and/or accessories may alter the warranty, controllability, and safety of the machine. Unauthorized modifications to the original equipment or failure to use original Toro parts could lead to serious injury or death. Unauthorized changes to the machine, engine, fuel or venting system, may violate applicable safety standards such as: ANSI, OSHA and NFPA and/or government regulations such as EPA and CARB.

Use care when checking blades. Wrap the blade(s) or wear gloves, and use caution when servicing them. Only replace damaged blades. Never straighten or weld them.

Use jack stands to support the machine and/or components when required.

CAUTION Raising the machine for service or maintenance relying solely on mechanical or hydraulic jacks could be dangerous. The mechanical or hydraulic jacks may not be enough support or may malfunction allowing the machine to fall, which could cause injury. Do not rely solely on mechanical or hydraulic jacks for support. Use adequate jack stands or equivalent support.

Carefully release pressure from components with stored energy.

Keep hands and feet away from moving parts. If possible, Do Not make adjustments with the engine running. If the maintenance or adjustment procedure require the engine to be running and components moving, use extreme caution.

WARNING Contact with moving parts or hot surfaces may cause personal injury. Keep your fingers, hands, and clothing clear of rotating components and hot surfaces.

Check all bolts frequently to maintain proper tightness.

30

Recommended Maintenance Schedule(s) Maintenance Service

Interval Maintenance Procedure

After the first 8 hours Change the engine oil.

Before each use or daily

Check the safety-interlock system. Clean and check the air-cleaner element. Check the engine-oil level. Clean the air intake screen. Inspect the blades. Inspect the grass deflector for damage.

After each use Clean the mower-deck housing.

Every 25 hours Grease all the lubrication points. Check tire pressure. Check the belts for wear or cracks.

Every 100 hours

Clean the paper air-cleaner element (more often in dirty or dusty conditions). Change the engine oil (more often in dirty or dusty conditions). Replace or clean and gap the spark plug. Replace the in-line fuel filter.

Every 200 hours Replace the paper air-cleaner element (more often in dirty or dusty conditions). Change the engine-oil filter (more often in dirty or dusty conditions).

Before storage Charge the battery and disconnect the battery cables. Perform all maintenance procedures listed above before storage. Paint any chipped surfaces.

Important: Refer to your engine owner's manual for additional maintenance procedures.

CAUTION If you leave the key in the switch, someone could accidently start the engine and seriously injure you or other bystanders. Shut off the engine and remove the key from the switch before you perform any maintenance.

31

Pre-Maintenance Procedures Raising the Seat Ensure that the parking brake is engaged. Lift the seat forward.

You can access following components by raising the seat: Serial plate Service decal Seat-adjustment bolts (if applicable) Fuel filter Battery and battery cables

Lubrication Greasing the Bearings Service Interval: Every 25 hoursGrease all the

lubrication points.

Grease Type: No. 2 lithium grease 1. Park the machine on a level surface, disengage

the blade-control switch, and engage the parking brake; refer to Park Position (page 13).

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Clean the grease fittings (Figure 27 and Figure 28) with a rag.

Note: Scrape any paint off the front of the fitting(s).

g032432

Figure 27

1. Front caster tire

decal106-8717

Figure 28 Located on the seat-pan underside

1. Read the instructions before servicing or performing maintenance

3. Grease every 25 operating hours

2. Check the tire pressure every 25 operating hours

4. Engine

4. Connect a grease gun to each fitting (Figure 27 and Figure 28).

5. Pump grease into the fittings until grease begins to ooze out of the bearings.

6. Wipe up any excess grease.

32

Engine Maintenance Engine Safety Shut off the engine before checking the oil or

adding oil to the crankcase. Keep your hands, feet, face, clothing, and other

body parts away the muffler and other hot surfaces.

Servicing the Air Cleaner Service Interval: Before each use or dailyClean

and check the air-cleaner element.

Note: Service the air cleaner more frequently (every few hours) if operating conditions are extremely dusty or sandy.

Removing the Air-Cleaner Paper Element 1. Park the machine on a level surface, disengage

the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Clean around the air-cleaner cover to prevent dirt from getting into the engine and causing damage.

4. Loosen the hose clamp and remove the paper element (Figure 29).

g207139

Figure 29

1. Cover 3. Hose clamp 2. Paper element

Servicing the Paper Air-Cleaner Element Service Interval: Every 100 hoursClean the paper

air-cleaner element (more often in dirty or dusty conditions).

Every 200 hoursReplace the paper air-cleaner element (more often in dirty or dusty conditions).

1. Clean the paper element by tapping it gently to remove dust.

Note: If it is very dirty, replace the paper element with a new one.

2. Inspect the element for tears, an oily film, or damage to the rubber seal.

3. Replace the paper element if it is damaged.

Important: Do not clean the paper filter.

Servicing the Engine Oil Engine-Oil Specifications Oil Type: Detergent oil (API service SF, SG, SH, SJ, or SL)

Crankcase Capacity: 1.8 L (61 fl oz); without filter; 2.1 L (70 fl oz) with filter

Viscosity: See the table below.

g017470

Figure 30

Checking the Engine-Oil Level Service Interval: Before each use or daily Note: Check the oil when the engine is cold. Important: If you overfill or underfill the engine crankcase with oil and run the engine, you may damage the engine. 1. Park the machine on a level surface, disengage

the blade-control switch (PTO), and engage the parking brake.

33

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

Note: Ensure that the engine is cool so that the oil has had time to drain into the sump.

3. To keep dirt, grass clippings, etc., out of the engine, clean the area around the oil-fill cap and dipstick before removing it (Figure 31).

g194611

Figure 31

Changing the Engine Oil Service Interval: After the first 8 hoursChange the

engine oil. Every 100 hoursChange the engine oil (more often in dirty or dusty conditions).

1. Park the machine so that the drain side is slightly lower than the opposite side to ensure that the oil drains completely.

2. Disengage the blade-control switch (PTO) and engage the parking brake.

3. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

4. Drain the oil from the engine (Figure 32).

g027539

Figure 32

5. Slowly pour approximately 80% of the specified oil into the filler tube and slowly add the additional oil to bring it to the Full mark (Figure 33).

34

g193530

Figure 33

6. Dispose of the used oil at a recycling center.

Changing the Engine-Oil Filter Service Interval: Every 200 hoursChange the

engine-oil filter (more often in dirty or dusty conditions).

1. Drain the oil from the engine; refer to Changing the Engine Oil (page 34).

2. Change the engine-oil filter (Figure 34).

g027477

Figure 34

Note: Ensure that the oil-filter gasket touches the engine, and then turn the oil filter an extra 3/4 turn.

3. Fill the crankcase with the proper type of new oil (Figure 33).

35

Servicing the Spark Plug Service Interval: Every 100 hours

Ensure that the air gap between the center and side electrodes is correct before installing the spark plug. Use a spark plug wrench for removing and installing the spark plug and a gapping tool or feeler gauge to check and adjust the air gap. Install a new spark plug if necessary.

Type of Spark Plug: NGK BPR4ES or equivalent

Air Gap: 0.75 mm (0.03 inch)

Removing the Spark Plug 1. Park the machine on a level surface, disengage

the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Clean the area around the base of the plug to keep dirt and debris out of the engine.

4. Remove the spark plug (Figure 35).

g027478

Figure 35

Checking the Spark Plug Important: Do not clean the spark plug(s). Always replace the spark plug(s) when it has a black coating, worn electrodes, an oily film, or cracks.

If you see light brown or gray on the insulator, the engine is operating properly. A black coating on the insulator usually means the air cleaner is dirty.

Set the gap to 0.75 mm (0.03 inch).

g206628

Figure 36

Installing the Spark Plug

g027661

Figure 37

Cleaning the Cooling System 1. Park the machine on a level surface, disengage

the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Remove the air filter from the engine. 4. Remove the engine shroud. 5. To prevent debris entering the air intake, install

the air filter to the filter base. 6. Clean debris and grass from the parts. 7. Remove the air filter and install the engine

shroud. 8. Install the air filter.

36

Fuel System Maintenance

DANGER In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. Refer to Adding Fuel (page 16) for a complete list of fuel related precautions.

Replacing the In-Line Fuel Filter Service Interval: Every 100 hoursReplace the

in-line fuel filter.

Never install a dirty filter after removing it from the fuel line. 1. Park the machine on a level surface, disengage

the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

g027590

g033082

Figure 38

37

Electrical System Maintenance Electrical System Safety Disconnect the battery before repairing the

machine. Disconnect the negative terminal first and the positive last. Connect the positive terminal first and the negative last.

Charge the battery in an open, well-ventilated area, away from sparks and flames. Unplug the charger before connecting or disconnecting the battery. Wear protective clothing and use insulated tools.

Servicing the Battery Removing the Battery

WARNING Battery terminals or metal tools could short against metal machine components, causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. When removing or installing the battery,

do not allow the battery terminals to touch any metal parts of the machine.

Do not allow metal tools to short between the battery terminals and metal parts of the machine.

1. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Raise the seat to access the battery. 4. Disconnect the negative (black) ground cable

from the battery post (Figure 39).

Note: Retain all fasteners.

WARNING Incorrectly removing the cables from battery could damage the machine and cables, causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. Always disconnect the negative

(black) battery cable before disconnecting the positive (red) cable.

Always connect the positive (red) battery cable before connecting the negative (black) cable.

5. Slide the rubber cover off the positive (red) cable.

6. Disconnect the positive (red) cable from the battery post (Figure 39).

Note: Retain all fasteners. 7. Remove the battery hold-down (Figure 39), and

lift the battery from the battery tray.

g017701

Figure 39

1. Battery 5. Negative () battery post 2. Positive (+) battery post 6. Wing nut, washer, and bolt 3. Bolt, washer, and nut 7. Battery hold-down 4. Terminal boot

38

Charging the Battery Service Interval: Before storageCharge the battery

and disconnect the battery cables. 1. Remove the battery from the chassis; refer to

Removing the Battery (page 38). 2. Charge the battery for a minimum of 1 hour at

6 to 10 A.

Note: Do not overcharge the battery. 3. When the battery is fully charged, unplug

the charger from the electrical outlet, then disconnect the charger leads from the battery posts (Figure 40).

g000538

Figure 40

1. Positive (+) battery post 3. Red (+) charger lead 2. Negative () battery post 4. Black () charger lead

Installing the Battery 1. Position the battery in the tray (Figure 39). 2. Using the fasteners previously removed, install

the positive (red) battery cable to the positive (+) battery terminal.

3. Using the fasteners previously removed, install the negative battery cable to the negative (-) battery terminal.

4. Slide the red terminal boot onto the positive (red) battery post.

5. Secure the battery with the hold-down (Figure 39).

6. Lower the seat.

Servicing the Fuses The electrical system is protected by fuses. It requires no maintenance; however, if a fuse blows, check the component/circuit for a malfunction or short.

Fuse type: MainF1 (30 A, blade-type) Charge CircuitF2 (25 A, blade-type) 1. Remove the screws securing the control panel

to the machine.

Note: Retain all fasteners. 2. Lift the control pane up to access the main wire

harness and fuse block (Figure 41). 3. To replace a fuse, pull out the fuse to remove

it (Figure 41).

g014921

Figure 41

1. Main (30 A) 2. Charge circuit (25 A)

4. Return the control panel to its original position.

Note: Use the screws removed previously to secure the panel to the machine.

39

Drive System Maintenance Checking the Tire Pressure Service Interval: Every 25 hoursCheck tire

pressure.

Maintain the air pressure in the front and rear tires as specified. Uneven tire pressure can cause an uneven cut. Check the pressure at the valve stem (Figure 42). Check the tires when they are cold to get the most accurate pressure reading.

Refer to the maximum pressure suggested by the tire manufacturer on the sidewall of the caster wheel tires.

Inflate the rear drive-wheel tires to 90 kPa (13 psi).

g000554

Figure 42

1. Valve stem

Releasing the Electric Brake You can manually release the electric brake by rotating the link arms forward. Once the electric brake is energized, the brake resets. 1. Turn the key to the OFF position or disconnect

the battery. 2. Locate the shaft on the electric brake where the

brake link arms are connected (Figure 43). 3. Rotate the shaft forward to release the brake.

g027911

Figure 43

1. Brake-link arm on the electric brake control module 2. Left, rear tire

40

Belt Maintenance Inspecting the Belts Service Interval: Every 25 hoursCheck the belts

for wear or cracks.

Replace the belt if it is worn. The signs of a worn belt include squealing while the belt is rotating; the blades slipping while cutting grass; and frayed edges, burn marks, and cracks on the belt.

Replacing the Mower Belt The signs of a worn belt include squealing while the belt is rotating, blades slipping while cutting grass, and frayed edges, burn marks, and cracks on the belt. Replace the mower belt if any of these conditions are evident. 1. Park the machine on a level surface, disengage

the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Set the height of cut at the lowest cutting position (38 mm (1-1/2 inches).

4. For machines with a 107 cm (42-inch) deck, remove the pulley covers (Figure 44).

g032555

Figure 44

1. Cover 2. Screw

5. Using a spring-removal tool (Toro Part No. 92-5771), remove the idler spring from the deck hook to remove tension on the idler pulley and roll the belt off the pulleys (Figure 45).

WARNING The spring is under tension when installed and can cause personal injury. Be careful when removing the belt.

g014930

Figure 45

1. Idler pulley 4. Spring 2. Mower belt 5. Engine pulley 3. Outside pulley 6. Spring-removal tool

6. Route the new belt around the engine pulley and mower pulleys (Figure 45).

7. Using a spring-removal tool (Toro Part No. 92-5771), install the idler spring over the deck hook and place tension on the idler pulley and the mower belt (Figure 45).

8. Install the pulley covers.

41

Mower Maintenance Blade Safety A worn or damaged blade can break, and a piece of the blade could be thrown toward you or bystanders, resulting in serious personal injury or death. Trying to repair a damaged blade may result in discontinued safety certification of the product. Inspect the blades periodically for wear or damage. Use care when checking the blades. Wrap the

blades or wear gloves, and use caution when servicing the blades. Only replace or sharpen the blades; never straighten or weld them.

On multi-bladed machines, take care as rotating 1 blade can cause other blades to rotate.

Servicing the Cutting Blades To ensure a superior quality of cut, keep the blades sharp. For convenient sharpening and replacement, keep extra blades on hand.

Before Inspecting or Servicing the Blades 1. Park the machine on a level surface, disengage

the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and disconnect the spark-plug wires from the spark plugs.

Inspecting the Blades Service Interval: Before each use or daily 1. Inspect the cutting edges (Figure 46). 2. If the edges are not sharp or have nicks, remove

and sharpen the blade; refer to Sharpening the Blades (page 44).

3. Inspect the blades, especially in the curved area. 4. If you notice any cracks, wear, or a slot forming

in this area, immediately install a new blade (Figure 46).

g006530

Figure 46

1. Cutting edge 3. Wear/slot forming 2. Curved area 4. Crack

Checking for Bent Blades Note: The machine must be on a level surface for the following procedure. 1. Raise the mower deck to the highest

height-of-cut position. 2. While wearing thickly padded gloves, or other

adequate hand protection, slowly rotate the blade into a position that allows you to measure the distance between the cutting edge and the level surface the machine is on (Figure 47).

g014972

Figure 47

1. Deck 3. Blade 2. Spindle housing

3. Measure from the tip of the blade to the flat surface (Figure 48).

42

g014973

Figure 48

1. Blade (in position for measuring) 2. Level surface 3. Measured distance between blade and the surface (A)

4. Rotate the same blade 180 degrees so that the opposing cutting edge is now in the same position (Figure 49).

g014974

Figure 49

1. Blade (side previously measured) 2. Measurement (position used previously) 3. Opposing side of blade being moved into measurement

position

5. Measure from the tip of the blade to the flat surface (Figure 50).

Note: The variance should be no more than 3 mm (1/8 inch).

g014973

Figure 50

1. Opposite blade edge (in position for measuring) 2. Level surface 3. Second measured distance between blade and surface (B)

A. If the difference between A and B is greater than 3 mm (1/8 inch), replace the blade with a new blade; refer to Removing the Blades (page 43) and Installing the Blades (page 44).

Note: If a bent blade is replaced with a new blade, and the dimension obtained continues to exceed 3 mm (1/8 inch), the blade spindle could be bent. Contact an Authorized Service Dealer for service.

B. If the variance is within constraints, move to the next blade.

6. Repeat this procedure on each blade.

Removing the Blades Replace the blades if they hit a solid object, or if the blade is out of balance or bent. 1. Hold the blade end using a rag or thickly padded

glove. 2. Remove the blade bolt, curved washer, and

blade from the spindle shaft (Figure 51).

43

g027833

Figure 51

1. Sail area of the blade 3. Curved washer 2. Blade 4. Blade bolt

Sharpening the Blades 1. Use a file to sharpen the cutting edge at both

ends of the blade (Figure 52).

Note: Maintain the original angle. Note: The blade retains its balance if the same amount of material is removed from both cutting edges.

g000552

Figure 52

1. Sharpen at original angle.

2. Check the balance of the blade by putting it on a blade balancer (Figure 53).

Note: If the blade stays in a horizontal position, the blade is balanced and can be used.

Note: If the blade is not balanced, file some metal off the end of the sail area only (Figure 52).

g000553

Figure 53

1. Blade 2. Balancer

3. Repeat this procedure until the blade is balanced.

Installing the Blades 1. Install the blade onto the spindle shaft (Figure

51).

Important: The curved part of the blade must be pointing upward toward the inside of the mower to ensure proper cutting.

2. Install the curved washer (cupped side toward the blade) and the blade bolt (Figure 51).

3. Torque the blade bolt to 47 to 88 Nm (35 to 65 ft-lb).

Leveling the Mower Deck Check to ensure that the mower deck is level any time you install the mower or when you see an uneven cut on your lawn.

Check the mower deck for bent blades prior to leveling; remove and replace any bent blades; refer to the Servicing the Cutting Blades (page 42) before continuing.

Level the mower deck side-to-side first, then adjust the front to rear slope.

Requirements: The machine must be on a level surface. All tires must be properly inflated; refer to Checking

the Tire Pressure (page 40).

Leveling from Side to Side 1. Park the machine on a level surface, disengage

the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Set the height-of-cut lever to the middle position. 4. Carefully rotate the blade(s) so that they are all

side to side (Figure 54).

44

g009682

Figure 54

1. Blades side to side 3. Outside cutting edges 2. Sail area of the blade 4. Measure from the tip of the

blade to the flat surface here.

5. Measure between the outside cutting edges and the flat surface (Figure 54).

Note: If both measurements are not within 5 mm (3/16 inch), an adjustment is required; continue with this procedure.

6. Move to the left side of the machine. 7. Loosen the side locking nut. 8. Raise or lower the left side of the mower deck

by rotating the rear locking nut (Figure 55).

Note: Rotate the rear locking nut clockwise to raise the mower deck; rotate the rear locking nut counter-clockwise to lower the mower deck (Figure 55).

g027588

Figure 55

1. Hanger bracket 3. Rear locking nut 2. Side locking nut

9. Check the side-to-side adjustments again; repeat this procedure until the measurements are correct.

10. Continue leveling the mower deck by checking the front-to-rear blade slope; refer to Adjusting the Front-to-Rear Blade Slope (page 45).

Adjusting the Front-to-Rear Blade Slope Check the front-to-rear blade level any time you install the mower. If the front of the mower is more than 7.9 mm (5/16 inch) lower than the rear of the mower, adjust the blade level using the following instructions: 1. Park the machine on a level surface, disengage

the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Set the height-of-cut lever to the middle position.

Note: Check and adjust the side-to-side blade level if you have not checked the setting; refer to Leveling from Side to Side (page 44).

4. Carefully rotate the blade(s) so they are facing front to rear (Figure 56).

g009658

Figure 56

1. Blades front to rear 2. Measure from the tip of the blade to the flat surface here.

5. Measure from the tip of the front blade to the flat surface, and the tip of the rear blade to the flat surface ( Figure 56).

Note: If the front blade tip is not 1.6 to 7.9 mm (1/16 to 5/16 inch) lower than the rear blade tip, adjust the front locknut.

6. To adjust the front-to-rear blade slope, rotate the adjustment nut in the front of the mower (Figure 57).

45

g014634

Figure 57

1. Adjusting rod 3. Locknut 2. Adjusting block

7. To raise the front of the mower, tighten the adjustment nut.

8. To lower the front of the mower, loosen the adjustment nut.

9. After adjustment, check the front-to-rear slope again, continue adjusting the nut until the front blade tip is 1.6 to 7.9 mm (1/16 to 5/16 inch) lower than the rear blade tip (Figure 56).

10. When the front-to-rear blade slope is correct, check the side-to-side level of the mower again; refer to Leveling from Side to Side (page 44).

Removing the Mower Deck 1. Park the machine on a level surface, disengage

the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Lower the height-of-cut lever to the lowest position.

4. Remove the hairpin cotter from the front support rod, and remove the rod from the deck bracket (Figure 58).

g014635

Figure 58

1. Front support rod 3. Deck bracket 2. Locking nut

5. Carefully lower the front of the mower deck to the ground.

6. Lift the mower deck and hanger brackets clear of the rear lift rod and lower the mower carefully to the ground (Figure 59).

g005077

Figure 59

1. Mower deck 3. Rear lift rod 2. Hanger bracket

7. Slide the mower deck rearward to remove the mower belt from the engine pulley.

46

8. Slide the mower deck out from underneath the machine.

Note: Retain all parts for future installation.

Installing the Mower Deck 1. Park the machine on a level surface, disengage

the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Slide the mower under the machine. 4. Lower the height-of-cut lever to the lowest

position. 5. Lift the rear of the mower deck and guide the

hanger brackets over the rear lift rod (Figure 59). 6. Attach the front support rod to the mower deck

with the clevis pin and hairpin cotter (Figure 58). 7. Install the mower belt onto the engine pulley;

refer to Replacing the Mower Belt (page 41).

Replacing the Grass Deflector Service Interval: Before each use or dailyInspect

the grass deflector for damage.

WARNING An uncovered discharge opening could allow the machine to throw objects toward you or bystanders, resulting in serious injury. Also, contact with the blade could occur. Never operate the machine without the grass deflector, the discharge cover, or the grass-collection system in place.

1. Remove the nut (3/8 inch) from the rod under the mower (Figure 60).

g005192

Figure 60

1. Mower deck 5. Spring 2. Grass deflector 6. Nut (3/8 inch) 3. Grass-deflector bracket 7. Short standoff 4. Rod

2. Slide the rod out of the short stand-off, spring, and grass deflector (Figure 60).

3. Remove the damaged or worn grass deflector. 4. Replace the grass deflector (Figure 60). 5. Slide the rod, straight end, through the rear

grass deflector bracket. 6. Place the spring on the rod, with end wires

down, and between the grass deflector brackets. 7. Slide the rod through the second grass-deflector

bracket (Figure 60). 8. Insert the rod at the front of the grass deflector

into the short standoff on the deck.

47

9. Secure the rear end of the rod into the mower with a nut (3/8 inch) as shown in Figure 60.

Important: The grass deflector must be spring-loaded in the down position. Lift the deflector up to test that it snaps into the full-down position.

Cleaning Washing the Underside of the Mower Deck Service Interval: After each useClean the

mower-deck housing.

Important: You can wash the machine with a mild detergent and water. Do not pressure wash the machine. Avoid excessive use of water, especially near the control panel, under the seat, around the engine, hydraulic pumps, and motors.

Wash the underside of the mower deck after each use to prevent grass buildup for improved mulch action and clipping dispersal. 1. Park the machine on a level surface, disengage

the blade-control switch (PTO), and engage the parking brake.

2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3. Attach the hose coupling to the end of the mower washout fitting, and turn the water on high (Figure 61).

Note: Spread petroleum jelly on the washout fitting O-ring to make the coupling slide on easier and protect the O-ring.

g003934

Figure 61

1. Washout fitting 3. O-ring 2. Hose 4. Coupling

4. Lower the mower to the lowest height-of-cut. 5. Sit on the seat and start the engine. 6. Engage the blade-control switch and let the

mower run for 1 to 3 minutes.

48

7. Disengage the blade-control switch, shut off the engine, remove the ignition key, and wait for all moving parts to stop.

8. Turn the water off and remove the coupling from the washout fitting.

Note: If the mower is not clean after 1 washing, soak it and let it stand for 30 minutes. Then, repeat the process.

9. Run the mower again for 1 to 3 minutes to remove excess water.

WARNING A broken or missing washout fitting could expose you and others to thrown objects or blade contact. Contact with a blade or thrown debris can cause injury or death. Replace broken or missing washout

fitting immediately, before using machine again.

Never put your hands or feet under the mower or through openings in the machine.

Disposing of Waste Engine oil, batteries, hydraulic fluid, and engine coolant are pollutants to the environment. Dispose of these according to your state and local regulations.

Storage Storage Safety Let the engine cool before storing the machine. Do not store the machine or fuel near flames or

drain the fuel indoors.

Cleaning and Storage 1. Disengage the blade-control switch (PTO), and

engage the parking brake. 2. Shut off the engine, remove the key, and wait

for all moving parts to stop before leaving the operating position.

3. Remove grass clippings, dirt, and grime from the external parts of the entire machine, especially the engine and hydraulic system. Clean dirt and chaff from the outside of the engine cylinder head fins and blower housing. Important: You can wash the machine with mild detergent and water. Do not pressure wash the machine. Avoid excessive use of water, especially near the control panel, engine, hydraulic pumps, and motors.

4. Check the parking brake operation; refer to Park Position (page 13).

5. Service the air cleaner; refer to Servicing the Air Cleaner (page 33).

6. Grease the machine; refer to Lubrication (page 32).

7. Change the crankcase oil; refer to Changing the Engine Oil (page 34).

8. Check the tire pressure; refer to Checking the Tire Pressure (page 40).

9. Charge the battery; refer to Charging the Battery (page 39).

10. Scrape any heavy buildup of grass and dirt from the underside of the mower, then wash the mower with a garden hose. Note: Run the machine with the blade-control switch (PTO) engaged and the engine at high idle for 2 to 5 minutes after washing.

11. Check the condition of the blades; refer to Servicing the Cutting Blades (page 42).

12. Prepare the machine for storage when non-use occurs over 30 days. Prepare the machine for storage as follows: A. Add a petroleum-based

stabilizer/conditioner to fuel in the tank. Follow mixing instructions from the stabilizer manufacturer. Do not use

49

an alcohol-based stabilizer (ethanol or methanol).

Note: A fuel stabilizer/conditioner is most effective when mixed with fresh fuel and used at all times.

B. Run the engine to distribute conditioned fuel through the fuel system (5 minutes).

C. Shut off the engine, allow it to cool, and drain the fuel tank.

D. Start the engine and run it until it stops. E. Dispose of fuel properly. Recycle the fuel

according to local codes.

Important: Do not store stabilizer/conditioned fuel over 90 days.

13. Remove and check the condition of the spark plug(s); refer to Servicing the Spark Plug (page 36). With the spark plug(s) removed from the engine, pour 30 ml (2 tablespoons) of engine oil into the spark plug hole. Use the starter to crank the engine and distribute the oil inside the cylinder. Install the spark plug(s). Do not install the wire on the spark plug(s).

14. Check and tighten all bolts, nuts, and screws. Repair or replace any part that is damaged.

15. Paint all scratched or bare metal surfaces. Paint is available from your Authorized Service Dealer.

16. Store the machine in a clean, dry garage or storage area. Remove the key from the switch and keep it out of reach of children or other unauthorized users. Cover the machine to protect it and keep it clean.

Storing the Battery 1. Fully charge the battery. 2. Let the battery rest for 24 hours, then check the

battery voltage.

Note: If the battery voltage is below 12.6 V, repeat steps 1 and 2.

3. Disconnect the cables from the battery. 4. Check the voltage periodically to ensure that the

voltage is 12.4 V or higher.

Note: If the battery voltage is below 12.4 V, repeat steps 1 and 2.

Battery Storage Tips Store the battery in a cool, dry area in an upright

position. Do not stack batteries directly on top of each other,

unless they are in cartons. Do not stack more than 3 batteries (only 2 if the

battery type is commercial). Test a wet battery every 4 to 6 months and charge

it, if necessary. Always test and charge the battery before

installation.

50

Troubleshooting Problem Possible Cause Corrective Action

The fuel tank is showing signs of collapsing or the machine is frequently showing signs of running out of fuel.

1. The air-cleaner paper element clogged. 1. Clean the paper element.

1. The engine load is excessive. 1. Reduce the ground speed.

2. The oil level in the crankcase is low. 2. Add oil to the crankcase. 3. The cooling fins and air passages

under the engine-blower housing are plugged.

3. Remove the obstruction from the cooling fins and air passages.

4. The air cleaner is dirty. 4. Clean or replace the air-cleaner element.

The engine overheats.

5. Dirt, water, or stale fuel is in the fuel system.

5. Contact an Authorized Service Dealer

1. The blade-control switch is engaged. 1. Disengage the blade-control switch.

2. The motion-control levers are not in the PARK position.

2. Move the motion-control levers outward to the PARK position.

3. The battery is dead. 3. Charge the battery. 4. The electrical connections are

corroded or loose. 4. Check the electrical connections for

good contact. 5. A fuse is blown. 5. Replace the fuse.

The starter does not crank.

6. A relay or switch is damaged. 6. Contact an Authorized Service Dealer.

1. The fuel tank is empty. 1. Fill the fuel tank.

2. The choke (if applicable) is not on. 2. Move the choke lever to the ON position.

3. The air cleaner is dirty. 3. Clean or replace the air-cleaner element.

4. The spark-plug wire(s) is loose or disconnected.

4. Install the wire(s) on the spark plug.

5. The spark plug(s) is pitted, fouled, or the gap is incorrect.

5. Install a new, correctly gapped spark plug(s).

6. There is dirt in fuel filter. 6. Replace the fuel filter. 7. Dirt, water, or stale fuel is in fuel

system. 7. Contact an Authorized Service Dealer.

8. There is incorrect fuel in the fuel tank. 8. Drain the tank and replace the fuel with the proper type.

The engine does not start, starts hard, or fails to keep running.

9. The oil level in the crankcase is low. 9. Add oil to the crankcase.

1. The engine load is excessive. 1. Reduce the ground speed.

2. The air cleaner is dirty. 2. Clean the air-cleaner element. 3. The oil level in the crankcase is low. 3. Add oil to the crankcase. 4. The cooling fins and air passages

under the engine blower housing are plugged.

4. Remove the obstruction from the cooling fins and air passages.

5. The spark plug(s) is pitted, fouled, or the gap is incorrect.

5. Install a new, correctly gapped spark plug(s).

6. The fuel-tank vent is blocked. 6. Contact an Authorized Service Dealer. 7. There is dirt in the fuel filter. 7. Replace the fuel filter. 8. Dirt, water, or stale fuel is in the fuel

system. 8. Contact an Authorized Service Dealer.

The engine loses power.

9. There is incorrect fuel in the fuel tank. 9. Drain the tank and replace the fuel with the proper type.

51

Problem Possible Cause Corrective Action

1. The bypass valves are open. 1. Close the tow valves.

2. The traction belts are worn, loose, or broken.

2. Contact an Authorized Service Dealer.

3. The traction belts are off the pulleys. 3. Contact an Authorized Service Dealer.

The machine does not drive.

4. The transmission has failed. 4. Contact an Authorized Service Dealer.

1. The cutting blade(s) is/are bent or unbalanced.

1. Install new cutting blade(s).

2. The blade mounting bolt is loose. 2. Tighten the blade mounting bolt. 3. The engine mounting bolts are loose. 3. Tighten the engine mounting bolts. 4. The engine pulley, idler pulley, or blade

pulley is loose. 4. Tighten the appropriate pulley.

5. The engine pulley is damaged. 5. Contact an Authorized Service Dealer. 6. The blade spindle is bent. 6. Contact an Authorized Service Dealer.

The machine vibrates abnormally.

7. The motor mount is loose or worn. 7. Contact an Authorized Service Dealer.

1. The blade(s) is not sharp. 1. Sharpen the blade(s).

2. A cutting blade(s) is/are bent. 2. Install a new cutting blade(s). 3. The mower is not level. 3. Level the mower from side-to-side and

front-to-rear. 4. An anti-scalp roller (if applicable) is not

set correctly. 4. Adjust the anti-scalp wheel height.

5. The underside of the mower deck is dirty.

5. Clean the underside of the mower deck.

6. The tire pressure is incorrect. 6. Adjust the tire pressure.

The cutting height is uneven.

7. A blade spindle is bent. 7. Contact an Authorized Service Dealer.

1. The drive belt is worn, loose or broken. 1. Install a new drive belt.

2. The drive belt is off of the pulley. 2. Install the drive belt and check the adjusting shafts and belt guides for the correct position.

3. The power-takeoff (PTO) switch or PTO clutch is faulty.

3. Contact an Authorized Service Dealer.

The blades do not rotate.

4. The mower belt is worn, loose, or broken.

4. Install a new mower belt.

52

Schematics

g028022

Electrical Diagram (Rev. A)

53

Notes:

California Proposition 65 Warning Information

What is this warning? You may see a product for sale that has a warning label like the following:

WARNING: Cancer and Reproductive Harmwww.p65Warnings.ca.gov.

What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California. It mandates that the Governor of California maintain and publish a list of chemicals known to cause cancer, birth defects, and/or other reproductive harm. The list, which is updated annually, includes hundreds of chemicals found in many everyday items. The purpose of Prop 65 is to inform the public about exposure to these chemicals.

Prop 65 does not ban the sale of products containing these chemicals but instead requires warnings on any product, product packaging, or literature with the product. Moreover, a Prop 65 warning does not mean that a product is in violation of any product safety standards or requirements. In fact, the California government has clarified that a Prop 65 warning is not the same as a regulatory decision that a product is safe or unsafe. Many of these chemicals have been used in everyday products for years without documented harm. For more information, go to https://oag.ca.gov/prop65/faqs-view-all.

A Prop 65 warning means that a company has either (1) evaluated the exposure and has concluded that it exceeds the no significant risk level; or (2) has chosen to provide a warning based on its understanding about the presence of a listed chemical without attempting to evaluate the exposure.

Does this law apply everywhere? Prop 65 warnings are required under California law only. These warnings are seen throughout California in a wide range of settings, including but not limited to restaurants, grocery stores, hotels, schools, and hospitals, and on a wide variety of products. Additionally, some online and mail order retailers provide Prop 65 warnings on their websites or in catalogs.

How do the California warnings compare to federal limits? Prop 65 standards are often more stringent than federal and international standards. There are various substances that require a Prop 65 warning at levels that are far lower than federal action limits. For example, the Prop 65 standard for warnings for lead is 0.5 g/day, which is well below the federal and international standards.

Why dont all similar products carry the warning? Products sold in California require Prop 65 labelling while similar products sold elsewhere do not.

A company involved in a Prop 65 lawsuit reaching a settlement may be required to use Prop 65 warnings for its products, but other companies making similar products may have no such requirement.

The enforcement of Prop 65 is inconsistent.

Companies may elect not to provide warnings because they conclude that they are not required to do so under Prop 65; a lack of warnings for a product does not mean that the product is free of listed chemicals at similar levels.

Why does Toro include this warning? Toro has chosen to provide consumers with as much information as possible so that they can make informed decisions about the products they buy and use. Toro provides warnings in certain cases based on its knowledge of the presence of one or more listed chemicals without evaluating the level of exposure, as not all the listed chemicals provide exposure limit requirements. While the exposure from Toro products may be negligible or well within the no significant risk range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does no